Front Trunk Hinge-Area Channel Covers for Model 3 Highland
This pair of formed ABS covers sits in the channels around the front-trunk hood-hinge areas. The left and right pieces have preformed openings for the original hardware. This selection is for left-hand-drive Model 3 Highland vehicles listed as 2024–2025.10.
- Two-Piece Set
- Formed ABS Covers
- LHD Only
- Preformed Openings
Hauptmerkmale
-
Two-Piece Set
The package contains a left and right cover for the front-trunk hinge-area channels.
-
Formed ABS Profiles
The covers are molded from ABS plastic to follow the surrounding pocket shapes.
-
Preformed Openings
The covers have separate openings and cutouts around the original hood-area hardware.
-
Listed LHD Version
This selection is for the left-hand-drive Model 3 Highland 2024–2025.10.
-
Removable for Cleaning
Remove accumulated debris regularly.
-
Hardware Clearance
Fit the exact cover profile with the hood actuator, connectors, hinges and drainage paths unobstructed.
Highlights
Left and Right Formed Covers
The package includes two different cover profiles for the opposite front-trunk hinge-area channels.
Openings Around Original Hardware
The preformed cutouts sit around the existing hood-area hardware. The actual actuator, connector, hinge travel and original drainage paths must remain unobstructed.
Keep the Channels Accessible
Use the matching removable covers with regular inspection and debris removal. Clear accumulated leaves and dirt without using a cover to seal a drain or conceal an existing drainage fault.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model 3 Highland | 2024–2025.10 | Left-hand drive only; exact hinge-area channel, hardware and cover profiles must match. |
This selection excludes right-hand-drive vehicles, the pre-Highland Model 3, Model Y, Model S and Model X.
Technische Daten
| Produkttyp | Front-trunk hinge-area channel cover set |
|---|---|
| Compatible Models | Tesla Model 3 Highland 2024–2025.10, left-hand drive only; actual profile must match |
| Position / Location | Left and right hinge-area channels at the rear sides of the front trunk |
| Material | ABS plastic |
| Farbe | Schwarz |
| Menge | 2 covers, one for each side |
| Installation Type | Fit into the original channel profiles |
| Hand Drive (LHD/RHD) | Left-hand drive only |
| Versandgewicht | 150 g |
What's in the Box
- 2×Front-trunk hinge-area channel covers, left and right
Installation
- Open the front hood.
- Clear loose debris.
- Fit each matching cover using its supplied retention instructions. Do not loosen original fasteners, disconnect the actuator, drill trim or force a cover against hood hardware. Leave the covers off if the correct retention and clearance cannot be established.
Gut zu wissen
Achtung
- The illustrated hood-area cylinder is part of the active-hood pedestrian-protection system on equipped vehicles. Do not loosen, disconnect, press on or modify the actuator, its wiring or original mounting hardware to fit a cover.
- Normal hood opening and closing does not establish active-hood deployment compatibility. These covers do not replace or repair the pedestrian-protection system or the original drainage system.
- Remove accumulated debris regularly. If a cover loosens, water pools, the hood binds or a vehicle warning appears, remove the affected accessory and arrange appropriate inspection before continued use.
Pflege
- Inspect cover retention and the surrounding channels regularly. Remove leaves and dirt promptly, then refit only after the original drainage paths are clear.
- Clean detached covers with a method suitable for ABS. Keep cleaning liquids and tools away from the hood actuator, connector and wiring.
FAQ
How many covers are included?
The package contains two formed channel covers, one for the left side and one for the right side of the front-trunk hinge area.
Does this selection fit right-hand-drive cars?
No. The listed selection is for left-hand-drive Model 3 Highland 2024–2025.10.
Do these covers guarantee protection from water damage?
They are removable channel covers, not a waterproof seal or a drain repair.
Can I adjust the hood actuator to make the cover fit?
Do not adjust, disconnect or modify the hood actuator, its connector or original mounting hardware for these covers.
English 
German 
Spanish 