A Real Carbon Fiber Shell for Your Center Armrest
This molded real carbon fiber shell wraps the center-console armrest lid of Tesla Model 3 (2017–2023) and pre-refresh Model Y (2020–2025.02), including its visible side profile. A custom locating structure holds it in place without adhesive or drilling. Available in Glossy, Matte or Forged.
- Real Carbon Fiber
- No Adhesive
- Top & Side Coverage
- 3 Finishes
- Model 3 & Y
Hauptmerkmale
-
Real Carbon Fiber Shell
A rigid molded carbon fiber cover changes the visible surface of the armrest lid
-
Top and Side Coverage
The shell follows the armrest-lid profile instead of covering only the flat top
-
Adhesive-Free Locating Fit
The molded underside seats around the factory lid with no tape, glue or drilling
-
Upholstery Protection
The original padded lid stays underneath, with a hard barrier above it
-
Three Finish Options
Choose Glossy, Matte or Forged for different levels of reflection and pattern
-
Release Opening Access
The molded underside leaves access around the factory release area
-
Easy Care
Wipe with a soft damp cloth and avoid abrasive cleaners
Highlights
A Hard-Shell Interior Upgrade
The original padded lid remains underneath. The molded cover changes the visible surface to real carbon fiber and creates a direct barrier between daily contact and the factory upholstery.
Molded Locating Fit
The custom-fit underside seats around the factory lid and uses its molded locating structure for retention, with no tape, glue, drilling or permanent modification.
Three Carbon Looks
Glossy shows a deeper woven pattern with more reflection, Matte is a quieter woven finish, and Forged is an irregular, marbled pattern rather than a uniform weave. The photo illustrates the matte woven finish.
Fitment by Generation
It fits the original center-armrest design of Model 3 (2017–2023) and Model Y (2020–2025.02). It does not fit Model 3 Highland, Model Y Juniper or the refreshed Model Y.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model 3 | 2017–2023 | Original center armrest design |
| Model Y | 2020–2025.02 | Pre-refresh center armrest design |
Does not fit Model 3 Highland (2024+) or the refreshed Model Y and Model Y Juniper.
Technische Daten
| Produkttyp | Molded carbon fiber center armrest cover |
|---|---|
| Compatible Models | Model 3 (2017–2023) and Model Y (2020–2025.02) |
| Position / Location | Front center-console armrest lid, top and visible sides |
| Material | Real molded carbon fiber |
| Surface Finish | Glossy, Matte or Forged pattern |
| Pattern / Weave | Woven (glossy and matte) or irregular forged pattern |
| Menge | 1 armrest cover |
| Installation Type | Molded locating structure; no adhesive, tape or drilling |
| Lieferumfang | 1 real carbon fiber center armrest cover |
| Care Instructions | Wipe with a soft damp cloth; avoid abrasive cleaners |
| Versandgewicht | 220 g (0.49 lb) |
What's in the Box
- 1×Real Carbon Fiber Center Armrest Cover
Installation
- Clean and fully dry the lid so nothing is trapped between the upholstery and the cover.
- Orient the cover and line up its front opening with the factory release area.
- Press progressively around the cover until the molded locating points are fully seated.
Gut zu wissen
Achtung
- Not for Model 3 Highland, Model Y Juniper or refreshed Model Y center consoles.
Pflege
- Wipe with a soft damp cloth and avoid abrasive cleaners.
FAQ
Is this a soft pad or a molded cover?
It is a rigid real carbon fiber shell that fits over the original center-armrest lid. It is not a padded slip-on cushion.
Will it fit a Model 3 Highland or Model Y Juniper?
No. It fits Model 3 (2017–2023) and Model Y (2020–2025.02) only.
Does it prevent the armrest compartment from opening?
No. The molded underside leaves access around the factory release area.
What exactly is included?
One real carbon fiber center-armrest cover. No adhesive is required or included.
English 
German 
Spanish 