A Strainer for the Washer Fluid Opening
This 304 stainless-steel mesh basket sits at a compatible windshield-washer fluid filler neck and screens leaves, grit and other visible particles while fluid is added. The support flange rests on the opening ledge without adhesive or drilling. Lift it out for cleaning, and use it only if the original cap closes and locks normally above it.
- 304 Stainless Mesh
- Drop-In Fit
- Abnehmbar
- No Adhesive
Hauptmerkmale
-
304 Stainless Mesh
A rigid stainless-steel mesh screen
-
Flange Seat
A flat support flange rests on the filler-neck ledge
-
Drop-In Fit
Installs with no adhesive, drilling or tools
-
Removable Basket
Lift it out to empty and rinse
-
Refill Screening
Catches visible debris as fluid is poured in
-
Cap Clearance
Use only when the original washer-fluid cap closes and locks normally
Highlights
Catches Debris at the Fill Point
The basket sits below the washer-fluid cap and intercepts visible solid debris such as leaves and grit while fluid passes through the mesh.
304 Stainless-Steel Mesh
The rigid 304 stainless-steel mesh screen has a flat support flange that rests on the filler-neck ledge, with no adhesive or drilling.
Lift Out and Rinse
With the cap open, lift the basket out, discard the captured debris away from the reservoir and rinse the mesh before reinstalling.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model 3 Highland | Drops into the washer-fluid filler neck under the original cap. | |
| Model Y | Drops into the washer-fluid filler neck under the original cap. |
The basket drops into the filler neck, rests on the ledge and sits under the original cap. There are no separate vehicle-size options.
Technische Daten
| Produkttyp | Windshield-washer fluid filler-neck strainer |
|---|---|
| Compatible Models | Model 3 Highland and compatible Model Y washer-fluid openings |
| Position / Location | Inside the windshield-washer fluid filler neck under the spray-symbol cap |
| Material | 304 stainless steel mesh |
| Farbe | Silver |
| Menge | 1 basket |
| Installation Type | Drop-in, removable, no adhesive, drilling or tools |
| Lieferumfang | 1 washer-fluid filter basket |
| Care Instructions | Lift out and rinse the mesh before reinstalling |
| Versandgewicht | 20 g (0.04 lb) |
What's in the Box
- 1×Washer-fluid filter basket
Installation
- With the vehicle parked, open the hood and identify the washer-fluid cap by the windshield-and-spray symbol.
- Wipe loose dirt and leaves away before opening the cap.
- Lower the clean basket into the filler neck so its support flange rests flat on the ledge.
- Add vehicle-appropriate washer fluid slowly; pause if fluid pools near the rim.
- Remove captured debris away from the reservoir, reseat the clean basket and close the cap.
Gut zu wissen
Achtung
- It is a washer-fluid strainer for the fill opening and does not repair a contaminated tank or an existing nozzle blockage.
Pflege
- Remove the basket and rinse the mesh outside the vehicle.
- Replace the basket if the flange or mesh is bent, split, loose or sharp.
- Do not push trapped debris through the mesh. Remove and empty the basket away from the open reservoir.
- Inspect before each refill and avoid bare-hand contact with damaged or sharp mesh.
FAQ
Where does the strainer go?
Inside the windshield-washer fluid filler neck, directly under the cap marked with the spray symbol.
Does it need adhesive?
No. It rests in the filler neck and stays removable for cleaning. Do not glue or tape it in place.
Can it clear a clogged nozzle?
No. It screens debris at the fill opening and does not clean a contaminated tank or clear an existing nozzle blockage.
What is included?
One 304 stainless-steel washer-fluid filter basket.
Does it fit Model Y Juniper or Model YL?
It is offered as one size for the Model Y washer-fluid opening; there are no separate Juniper or YL options.
English 
German 
Spanish 