Jack Pad Adapter Set with Storage Case
A set of four black rubber lift-point adapters with red retention rings and a zippered storage case. The molded post and broad contact disc are intended for matching designated body lifting points on Model 3, Model Y, Model S and Model X. Available in 25 mm and 20 mm sizes.
- 4 Pads
- Aufbewahrungsetui
- Rubber Contact
- 20 mm / 25 mm
Hauptmerkmale
-
Rubber Contact Disc
A broad rubber base provides the interface between a suitable lifting saddle and the designated vehicle lift point.
-
Locating Post
The molded post locates in the lift-point opening.
-
Temporary O-Ring Retention
The red ring helps retain the pad during positioning and is not a lifting lock.
-
Four-Pad Set
Four separate adapters are supplied for workshop lifting-point setup.
-
Zippered Storage Case
The included case keeps the pads together between uses.
-
Two Size Selections
Choose the 25 mm option or the 20 mm option labeled for the Tesla Germany factory.
Highlights
Four Pads and Storage Case
Four adapters sit in the zippered case. The separate pad pictured beside it shows the molded post and red retention ring.
Contact-Surface Illustration
The rubber disc sits between a compatible lifting saddle and the designated lift point. This illustration shows the contact arrangement.
Choose the Matching Size
The selections are 25 mm and 20 mm (for Tesla Germany Factory).
Vehicle Lifting Preparation
Use designated body lift points and the correct rated equipment. Air-suspension vehicles require Jack Mode before lifting; the charging cable must be disconnected.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model 3 | Fits the designated body lifting points. | |
| Model Y | 20 mm option is labeled for Germany-factory vehicles. | |
| Model S | Fits the designated body lifting points; enable Jack Mode if equipped with air suspension. | |
| Model X | Fits the designated body lifting points; enable Jack Mode if equipped with air suspension. |
The 20 mm size is labeled for Tesla Germany Factory vehicles. No separate Model YL fit is established by this description.
Technische Daten
| Produkttyp | Jack pad adapter set with storage case |
|---|---|
| Compatible Models | Model 3, Model Y, Model S and Model X with a matching designated body lift-point interface |
| Position / Location | Vehicle-designated body lifting points only |
| Material | Rubber pads with retention O-rings |
| Farbe | Black pads with red retention rings |
| Menge | 4 pads and 1 zippered storage case |
| Gewicht | 720 g (1.59 lb), listed shipping weight for each option |
| Size Options | 25 mm; 20 mm (for Tesla Germany Factory), as labeled selections |
What's in the Box
- 4×Jack pad adapters
- 1×Zippered storage case
Installation
- Locate the designated body lift points.
- Disconnect the charging cable. Enable Jack Mode on vehicles equipped with air suspension.
- Place the adapter in the lift-point opening so the rubber contact disc sits between the saddle and the lift point.
- Center the suitable lifting saddle beneath the pad and lift.
Gut zu wissen
Achtung
- Use only the vehicle-designated body lifting points; never lift beneath the battery or side rails.
- Disconnect the charging cable before lifting. On vehicles with air suspension, enable Jack Mode before lifting.
- Use rated lifting equipment on a firm level surface, follow its instructions and engage lift safety locks. Never work beneath a vehicle supported only by a jack; use correctly rated independent supports or a suitable lift.
- The O-ring provides temporary positioning retention, not a load lock. Do not force a mismatched post, drill the lift point or use a damaged pad.
Pflege
- Inspect rubber and retention rings before each use; replace damaged or deformed pads.
- Clean off dirt and debris, then dry before storing the set in its case.
- Remove the pads after use. The retention rings are for temporary positioning, not permanent installation.
FAQ
Which size should I select?
Choose between the labeled 25 mm option and 20 mm (for Tesla Germany Factory) option. The 20 mm size is labeled for Tesla Germany Factory vehicles.
What is included?
Four jack pad adapters and one zippered storage case.
Does the O-ring lock the vehicle to the jack?
No. It provides temporary retention while positioning the adapter. It is not a load lock or a substitute for correct lifting contact and support equipment.
Do air-suspension vehicles need preparation?
Yes. Enable Jack Mode before lifting if equipped with air suspension. Disconnect the charging cable on all vehicles before lifting.
Can I work underneath with only a jack supporting the car?
No. A jack alone is not a support for working underneath.
English 
German 
Spanish 