Carbon Fiber Fog Light Trim with Glossy, Matte & Forged Finishes for Tesla Model Y

Carbon-Fiber Trim for the Front Lamp Area

Add molded carbon-fiber overlays around the front lower-lamp area of the selected Model Y version. The two-piece set uses included 3M double-sided tape and offers wet or dry carbon with glossy, matte or forged finishes. The trim does not replace the light or add lighting functions.

Real Carbon Fiber
Wet or Dry Carbon
3M Tape Included
2-Piece Set

Hauptmerkmale

Carbon-fiber overlays

Molded trim adds a carbon finish around the front lower-lamp area without replacing the lamp assembly.
Wet or dry option

Select the carbon construction option and vehicle version before choosing a finish.
Three finishes

Glossy, matte and forged carbon are separate choices; the forged appearance differs from the woven pattern.
Two-piece set

The set contains one trim for each side of the front bumper lamp area.
Adhesive mounting

Included 3M double-sided tape attaches the overlays; dry-fit the actual trim before exposing the liner.
Protective coating

The coated finish still needs routine care; sunlight and outdoor exposure can affect its appearance over time.

Highlights

Forged Finish - TESVX Fog Light Trim — Forged Finish

The forged option has a varied flake-like appearance rather than the regular woven pattern. Choose the intended finish as well as the wet or dry construction option.

Original-Generation Lamp Area - TESVX Fog Light Trim — Original-Generation Lamp Area

The installed example shows an original-generation Model Y lamp opening. Juniper and Model YL use a separate profile.

Woven Trim Pair

The woven finishes use a regular twill pattern; forged carbon has a different varied appearance. Select the intended wet or dry construction and finish for the correct bumper version.

Align the Adhesive Fit

Included 3M double-sided tape bonds the trim to a clean, dry mounting surface.

Kompatibilität

Modell	Years / Version	Hinweise
Model Y	2020–2025.03	2-piece set; wet or dry carbon
Model Y Juniper	2025+	Shared option with Model YL; wet or dry carbon
Model YL	2026+	Shared option with Model Y Juniper; wet or dry carbon

Original Model Y and Juniper/Model YL options differ. Does not fit Model 3.

Technische Daten

Produkttyp	Real carbon fiber fog light (air blade) trim overlay, 2 pieces
Compatible Models	Model Y (2020–2025.03), Model Y Juniper (2025+), Model YL (2026+)
Position / Location	Front lower-lamp trim area; original housing remains
Material	Molded carbon fiber; wet or dry option with protective coating
Surface Finish	Glossy, matte or forged carbon fiber
Pattern / Weave	2×2 twill for woven finishes; forged-pattern finish differs
Menge	2 pieces
Installation Type	3M double-sided tape provided; no drilling or cutting
Lieferumfang	2 fog light trims, 1 piece of 3M double-sided adhesive tape
Versandgewicht	150 g (0.33 lb)

What's in the Box

2×Real carbon fiber fog light trims
1×3M double-sided adhesive tape

Installation

Difficulty: Moderate
Zeit: Allow time for alignment and adhesive curing
Werkzeuge: Soft cloth and gentle controlled warmth if needed

Clean the mounting surfaces with a finish-compatible cleaner, remove oil and wax, and dry fully.
If warming the tape is needed, use gentle controlled warmth below 40°C.
Expose the liner without touching the adhesive, align carefully and press evenly for at least 20–30 seconds.
Keep dry for 48 hours.

Gut zu wissen

Achtung

Do not cover the lamp lens, block required lighting or obstruct nearby sensors and openings.
This trim adds an exterior overlay; it does not improve lamp performance or establish road approval.
Avoid excessive heat when fitting the tape; hand-laid carbon patterns and finish appearance can vary.