Three-Piece ABS Front Lip for Model Y Juniper and Model YL
This three-piece ABS front lip fits the redesigned bumper on Model Y Juniper (2025+) and Model YL (2026+). A center segment and two side segments use pre-applied 3M VHB tape. Choose Matte Black, Glossy Black, Matte Carbon texture or Glossy Carbon texture; the carbon options are finishes on ABS, not carbon-fiber construction.
- Juniper & YL Fit
- ABS Plastic
- Three Pieces
- 4 Finishes
- 3M VHB Tape
Hauptmerkmale
-
Refreshed Bumper Fit
Designed for Model Y Juniper (2025+) and Model YL (2026+)
-
ABS Construction
ABS plastic front lip segments
-
Zero Drilling Install
Pre-applied automotive-grade 3M VHB tape means a non-invasive peel-and-stick installation
-
Three-Piece Modular Design
A center segment and left and right side segments make alignment easy
-
UV-Resistant Clear Coat
Every finish is coated to help prevent yellowing and fading
-
Four Finish Options
Choose Matte Black, Glossy Black, Matte Carbon texture or Glossy Carbon texture
-
Lower Front Styling
Adds a lip along the lower front bumper
Highlights
Refreshed Front Bumper Fit
Designed for Model Y Juniper (2025+) and Model YL (2026+), with a shape that follows the redesigned lower bumper. It is not compatible with Model Y 2020–2024.
Lower Front Styling
The front lip adds a shaped edge below the front bumper.
Three ABS Segments
The kit comprises one center lip segment and two side segments. Test-fit all pieces with the adhesive backing still attached.
Four Surface Finishes
Choose Matte Black, Glossy Black, Matte Carbon texture or Glossy Carbon texture. Carbon texture describes the finish; the lip body is ABS.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model Y Juniper | 2025+ | Redesigned front bumper |
| Model YL | 2026+ | Redesigned front bumper |
Not compatible with Model Y 2020–2024. Complete a test fit with the adhesive backing still on before final application.
Technische Daten
| Produkttyp | 3-piece front lip spoiler |
|---|---|
| Compatible Models | Model Y Juniper (2025+) and Model YL (2026+) |
| Position / Location | Lower front bumper |
| Material | High-quality ABS plastic with UV-resistant clear coat |
| Surface Finish | Glossy Black, Matte Black, Matte Carbon texture, Glossy Carbon texture |
| Menge | 3 pieces (1 center + 2 side) |
| Installation Type | Pre-applied 3M VHB tape; peel-and-stick |
| Drilling Required | Nein |
| Lieferumfang | Center lip segment, left and right side lip segments, installation guide |
| Care Instructions | Cure 48-72 hours before highway speeds or washing; automatic car wash after 7 days |
| Versandgewicht | 12 kg (26.5 lb) |
What's in the Box
- 1×Center Lip Segment
- 2×Side Lip Segments (Left and Right)
- 1×Installation Guide
Installation
- Wipe the lower bumper with isopropyl alcohol, remove wax, dirt or ceramic coating from the adhesion area and let it dry; install at 15-30°C (59-86°F).
- Assemble the 3 pieces and position them with the adhesive backing still on, using masking tape to mark the alignment.
- Lightly heat the 3M tape with a hair dryer for 30-60 seconds to activate the adhesive.
- Peel the backing from the center piece, align it with your marks and press firmly for 30 seconds, then repeat for the side pieces.
- Hold pressure with painter's tape overnight; the adhesive takes 48-72 hours to bond fully.
Gut zu wissen
Achtung
- Test-fit every segment with the adhesive backing still on.
- Install at 15-30°C (59-86°F) and allow 48-72 hours to cure before highway speeds or washing.
- Use automatic car washes only after the 7-day adhesive cure and avoid pointing high-pressure washers at the seams.
- Fits Model Y Juniper (2025+) and Model YL (2026+) only.
Pflege
- Clean regularly with pH-neutral car soap and a soft microfiber towel.
- Use automatic car washes only after the initial 7-day adhesive cure, and avoid pointing high-pressure washers at the seams.
FAQ
Do I need to drill holes to install this?
No. The 3-piece lip comes with pre-applied automotive-grade 3M VHB tape. Clean the bumper, align and press firmly; no permanent modifications are required.
Will this fit older Model Y versions (2020-2024)?
No. It is engineered exclusively for the redesigned front bumper of the Model Y Juniper (2025+) and Model YL (2026+).
What if I want to remove it before selling the car?
The tape is removable. Apply gentle heat, slice through the tape with dental floss or fishing line behind the lip, and wipe any residue away with adhesive remover.
Are the carbon finishes made from carbon fiber?
No. The material is ABS plastic; Matte Carbon and Glossy Carbon are texture finishes.
What parts are included?
The source lists one center lip segment, two side lip segments for left and right, and an installation guide.
English 
German 
Spanish 