Add Depth to Your Frunk Logo
A hollow aluminum-alloy overlay adds a dimensional outline around the factory front trunk T logo. Available in silver, grey or black for the original Model 3 and Model Y, with a foam-tape backing.
- Aluminiumlegierung
- 3D Hollow Design
- Peel & Stick
- 3 Finishes
Hauptmerkmale
-
3D Hollow Design
The dimensional cutout surrounds the front T logo and leaves it visible
-
Aluminiumlegierung
The metal overlay adds a shaped outer accent to the emblem
-
Frunk Position
Made for the factory front trunk T logo of the selected original Model 3 and Model Y versions
-
Three Finishes
Choose silver, grey or black
-
Foam Tape Backing
Double-sided foam tape secures the overlay to a suitable cleaned surface
-
Original Logo Retained
The cutouts sit over the existing logo
Highlights
Silver Outline
The silver overlay frames the existing T logo with a shaped metal outline.
Black Finish
The black version offers the same cutout pattern in a dark finish.
Grey Finish
Grey provides a metallic middle tone. Choose the color shown for your selection.
Foam-Tape Backing
The back carries double-sided foam adhesive. Test-fit the shape with the liner attached before application.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model 3 | 2017–2023.10 | Original model; not Model 3 Highland |
| Model Y | 2020–2024 | Original model; not Model Y Juniper |
Fits original Model 3 through October 2023 and Model Y through 2024. Does not fit Highland or Juniper.
Technische Daten
| Produkttyp | 3D metal frunk logo badge overlay |
|---|---|
| Compatible Models | Model 3 (2017–2023.10), Model Y (2020–2024) |
| Position / Location | Front trunk (frunk) T logo |
| Material | Aluminiumlegierung |
| Surface Finish | 3D hollow cutout design |
| Farbe | Silver / Grey / Black |
| Menge | 1 Stück |
| Abmessungen | 15 × 11 × 0.5 cm |
| Installation Type | Peel-and-stick with double-sided foam tape; no tools required |
| Lieferumfang | 1 badge overlay (finish as selected), pre-applied double-sided foam adhesive, installation instructions |
| Care Instructions | Wait 24 hours before washing; avoid high-pressure washers on the badge |
| Versandgewicht | 120 g (0.26 lb) |
What's in the Box
- 1×3D metal frunk logo badge overlay (finish as selected) with pre-applied double-sided foam adhesive
- 1×Installation instructions
Installation
- Test-align the overlay over the existing front T logo with the liner still attached.
- Clean the contact area with a finish-compatible cleaner and let it dry fully.
- Remove the adhesive liner, center the cutouts over the logo and apply even pressure across the contact areas.
- Wait 24 hours before washing.
Gut zu wissen
Achtung
- Does not fit Highland or Juniper.
- Wait 24 hours before washing and avoid high-pressure spray directly on the overlay.
Pflege
- Wait 24 hours after installation before washing; hand wash for the first few weeks.
- Avoid high-pressure washers directly on the badge and use pH-neutral soap.
- Inspect adhesion periodically.
FAQ
Does the original T logo stay in place?
Yes. The cutout overlay sits around the existing front T logo.
Does it fit Highland or Juniper?
The listed option covers original Model 3 2017–October 2023 and Model Y 2020–2024. Highland and Juniper compatibility is not specified for this option.
Can I remove the overlay?
Yes. Adhesive residue and finish condition after removal depend on the surface.
When can I wash the car?
Wait 24 hours after application and avoid high-pressure spray directly at the overlay.
English 
German 
Spanish 