An Adjustable Clamp Mount for Parked Starlink Mini Setups
This clamp mount connects a Starlink Mini to a suitable RV ladder, railing, table edge or roof-rack support without drilling mounting holes. Its screw-operated jaws cover a 0.75–2 inch clamping range, and the ball-joint arm lets you position the antenna before tightening. The top adapter connects to the Mini mounting base; for stationary use only.
- Starlink Mini
- Adjustable Clamp
- Ball-Joint Arm
- No Support Drilling
Hauptmerkmale
-
Adjustable Clamp
The screw-operated jaws fit suitable round or square bars within the 0.75–2 inch size range.
-
Mini Adapter Connection
The round top adapter connects to the matching Mini mounting base.
-
Positioning Arm
Two ball joints allow the antenna position to be set before the arm’s hand knob is tightened.
-
No Mounting Holes
The clamp attaches to a suitable support without drilling it.
-
Metal Construction
The black metal clamp and arm use an aluminum-alloy construction.
-
Removable Setup
The hand-operated clamp can be released for storage or relocation while the vehicle is parked.
Highlights
Clamp, Arm and Top Adapter
The mount combines adjustable jaws, a two-joint positioning arm and the round Mini adapter.
Mini Mounting Base
The top adapter secures to the matching Mini mounting base. The antenna is separate equipment.
Set Up While Parked
Use a rigid support and tighten the clamp and arm before positioning the antenna. The hand-tight clamp has no wind or road-vibration rating.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Starlink Mini | Matching mounting base and adapter; suitable support in the 0.75–2 in clamping range. |
The stated clamp range does not guarantee grip on every round bar, square bar or table edge. Use only a rigid support with full jaw contact.
Technische Daten
| Produkttyp | Adjustable clamp mount for Starlink Mini |
|---|---|
| Compatible Models | Starlink Mini with matching mounting base and top adapter |
| Position / Location | Suitable RV ladder, railing, table edge or roof-rack support; stationary use |
| Material | Aluminum alloy / metal construction |
| Farbe | Schwarz |
| Abmessungen | Clamping size range: approx. 1.9–5.1 cm (0.75–2 in) |
| Installation Type | Screw-operated clamp, adjustable ball-joint arm and Mini adapter |
| Drilling Required | No support drilling for clamp attachment |
Installation
- Choose a rigid support within the clamp’s size range.
- Connect the top adapter to the matching Mini mounting base, then engage the base fully with the antenna.
- Tighten the clamp onto the support. Set the ball-joint arm position and tighten its hand knob.
- Route the cable without strain.
Gut zu wissen
Achtung
- Use only on a rigid support able to carry the antenna and mount.
- For stationary setups; the clamp has no in-motion, vibration or wind-load rating.
- Do not drill new holes in the antenna or modify its housing to make it fit.
- Clamping can mark or deform a soft, thin or coated support. No-drill attachment does not guarantee damage-free removal.
- Keep the cable free from strain and sharp edges, and choose a position with an unobstructed sky view.
FAQ
What size support does the clamp accept?
The clamping range is approximately 0.75–2 inches (1.9–5.1 cm).
Do I need to drill mounting holes?
No support drilling is needed for the clamp attachment. The Mini needs its matching mounting base; do not drill or modify the antenna housing.
Can it remain installed while driving?
No. Use it while stationary and remove the antenna and clamp before moving the vehicle.
How is the antenna angle set?
Adjust the ball-joint arm to the required position and tighten the hand knob.
English 
German 
Spanish 