Four-Cup Suction Mount for Starlink Mini
A silicone case holds the Starlink Mini within a frame with four lever-operated suction cups. Use it for a temporary setup on a parked vehicle or other stationary, smooth, non-porous surface.
- Starlink Mini
- Four Suction Cups
- Silicone Case
- Removable Attachment
- Stationary Use
Hauptmerkmale
-
Mini-Shaped Frame
The silicone case wraps around the Mini housing; fit the device into the frame before placing the mount.
-
Four Suction Cups
A cup at each corner uses a lever to engage and release its seal.
-
Removable Attachment
The surface attachment uses suction rather than drilling or adhesive. Release the seals before lifting it away.
-
Smooth Surface Contact
Each cup needs a clean, dry, non-porous contact area with no gaps at its rim.
-
Temporary Stationary Use
Set up while parked and remove the mount and Mini before moving the vehicle.
-
Reusable Setup
Clean the cups between uses and inspect their rims and levers before each installation.
Highlights
Silicone Case and Four Corner Cups
The frame wraps around the Mini housing, with a lever-operated cup at each corner. Its black textured case has a rear opening around the exposed portion of the Mini housing.
Fit the Mini Before Mounting
Seat the Mini fully in the silicone case before positioning the assembled mount.
Four Cup Seals
Each of the four cups seals with its own lever.
Remove Before Vehicle Movement
This setup is for temporary stationary use.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Starlink Mini | Mini-shaped silicone frame. |
Choose a smooth, non-porous surface that allows full contact at all four cups. Glass, painted metal and fiberglass require suitable surface condition and curvature.
Technische Daten
| Produkttyp | Silicone-frame suction cup mount |
|---|---|
| Compatible Models | Starlink Mini |
| Position / Location | Smooth, non-porous surface with full contact beneath all four cups |
| Material | Protective silicone case |
| Installation Type | Four lever-operated suction cups; removable without drilling or adhesive |
| Lieferumfang | Suction cup mount with silicone case; installation instructions |
| Color / Finish | Black, with a textured case surface |
What's in the Box
- 1×Suction cup mount with silicone case
- Installation instructions
Installation
- Park the vehicle and choose a stationary location with unobstructed sky view and a surface that permits suction mounting. Inspect every cup rim and lever.
- Disconnect the Mini and fit it fully into the silicone case.
- Clean and completely dry the surface and cup contact areas with suitable products. Position the assembled frame so all four cup rims can seal without gaps.
- Press each cup into contact and engage its lever.
- Route and support the cable independently, then reconnect the Mini. Monitor the seals while in use; support the assembly and release every seal before removal or vehicle movement.
Gut zu wissen
Achtung
- For stationary use only.
- Not for rough, porous, uneven or heavily curved surfaces. Wax, grit and oils can interfere with the seal; use cleaning products suitable for the mounting surface.
- Keep the Mini antenna face, connectors and required clearances unobstructed. Support its cable separately so it cannot pull on the frame or cup seals.
- Choose a mounting-surface temperature of 5°C–38°C (40°F–100°F) for installation and avoid hot surfaces in direct sunlight. Recheck all seals as surface conditions change.
Pflege
- Rinse dirt from the suction cups with water and let them dry before storage. Wipe the case with a soft cloth and keep grit away from the contact surfaces.
- Store in a cool, dry location. Replace or stop using damaged cups or levers; do not pry a sealed cup from the surface.
FAQ
Which Starlink model fits the frame?
The silicone frame is shaped for Starlink Mini.
Can I drive with it attached?
No. This mount is for temporary stationary setups only.
Which surfaces can accept the cups?
Use smooth, dry, non-porous surfaces where each cup rim has full contact. Rough, porous, waxy or strongly curved areas are unsuitable.
How do I install and release the mount?
Fit the Mini into the silicone case first. Clean and dry the surface, seat all four cups and engage their levers. To remove, support the assembly, release every seal and lift it away.
Is the Mini included?
The package lists the suction cup mount with silicone case and installation instructions. The Mini and its power equipment are separate.
English 
German 
Spanish 