Starlink Mini Suction Mount for the Holed Kickstand
This crossbar mount connects to the original Starlink Mini kickstand version with mounting holes and uses two suction cups on suitable glass. It is a removable accessory for a temporary parked setup. The Mini terminal and original kickstand are separate.
- Starlink Mini
- Holed Kickstand Required
- Two Suction Cups
- Temporary Parked Setup
Hauptmerkmale
-
Hole-pattern fit
The metal bar attaches to the original Mini kickstand version with mounting holes.
-
Two suction cups
One cup sits at each end of the crossbar to contact a suitable glass surface. Both cups need full contact.
-
Assembled connection
The pictured installation uses long fasteners at the kickstand and shorter fasteners at the cups; assembly tools are required.
-
Temporary glass position
Use a clean, dry, smooth and flat mounting area with enough space for both cups and the Mini.
-
Portable mount
Release the suction cups and remove the assembly when changing locations; do not pull on the Mini to detach it.
-
Separate kickstand
The original Mini kickstand and the Mini terminal are not included with this accessory.
Highlights
Crossbar with Two Cups
The crossbar spans the Mini’s original kickstand, with one suction cup at each end. Both cups need a full seal on the chosen glass area.
Kickstand Holes
The original kickstand must have the matching mounting holes. The kickstand shown is not included.
Assembly Before Glass Attachment
The product diagram shows long fasteners joining the bar to the kickstand and shorter fasteners joining the cups.
Removable Parked Setup
Choose a clear mounting area for a temporary parked installation.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Starlink Mini | Original kickstand with matching mounting holes required; kickstand and Mini excluded. |
A hole-free version is not interchangeable with the illustrated mounting interface.
Technische Daten
| Produkttyp | Starlink Mini kickstand crossbar suction mount |
|---|---|
| Compatible Models | Starlink Mini with original kickstand version with mounting holes |
| Position / Location | Suitable smooth, flat glass; temporary parked setup |
| Menge | Two suction cups on one mount assembly |
| Installation Type | Fastened kickstand/cup assembly; suction attachment to glass |
| Lieferumfang | Suction mount assembly; Mini and original kickstand excluded |
| Versandgewicht | 300 g |
What's in the Box
- 1×Suction mount assembly with crossbar and two suction cups
- Original Starlink Mini kickstand and Mini terminal not included
Installation
- Align the kickstand with the metal bar and fasten it using the longer fasteners shown in the product diagram. Attach the cups at each end with the corresponding shorter fasteners.
- Engage the kickstand with the Mini’s rear slot. Tighten the hardware with the correct tools without damaging the kickstand.
- Clean and dry a suitable flat glass area. Remove any cup protection films, place both cups with full contact and operate their locking levers.
Gut zu wissen
Achtung
- Requires the original Mini kickstand with matching mounting holes. If the holes are absent or misaligned, stop and obtain a compatible kickstand; do not drill a different version to force the fit.
- For temporary use while parked. High-speed retention is not a supported rating for this mount.
- Both cups must sit fully on clean, dry, smooth, flat and undamaged glass. Avoid cracks, curved areas, textured surfaces and loose films.
- Keep the driver’s view, airbag areas, controls, exits and moving window or sunroof mechanisms clear. Remove the mount before operating the glass.
- Glass and surrounding bodywork can obstruct the antenna.
Pflege
- Keep the cup faces clean and free of grit. Clean gently and dry before storage.
- Inspect cup edges, levers, mounting fasteners and the kickstand for damage; replace damaged parts before reuse.
FAQ
Is the original kickstand included?
No. This accessory uses your separate original Mini kickstand with matching mounting holes; the Mini terminal is also separate.
What if my kickstand has no holes?
The mount requires the kickstand version with mounting holes. Do not drill a different version to make it fit this mount.
Is assembly tool-free?
No. The pictured bar and suction cups are fastened to the kickstand with screws and nuts.
Can I leave it outside while driving?
It is for a temporary parked setup. The product does not provide a supported high-speed retention rating.
Will mounting behind glass guarantee a signal?
No. Glass and surrounding vehicle structure can obstruct the antenna.
English 
German 
Spanish 