Six Complete Front Control Arms for the Pre-Juniper Model Y
This kit contains six complete front arm assemblies for the Tesla Model Y 2020-2024: both upper arms, both straight lower arms and both curved banana arms, each with ball joints and bushings already pressed in. The arms are aftermarket assemblies built to the Tesla OE numbers listed in the fit table. It does not fit the Model Y Juniper 2025+ or the Model 3.
- 6 Front Assemblies
- Pressed Joints and Bushings
- OE Reference Matching
- Model Y 2020–2024
Hauptmerkmale
-
Six Front Arm Assemblies
Two upper, two straight lower and two curved lower arms.
-
Preassembled Joints and Bushings
The assemblies include pressed-in ball joints and bushings.
-
Model Y Straight-Arm Reference
Two straight lower arms use reference 1188341-00-C.
-
OE References
Built to the listed arm references and revision letters.
-
Aftermarket Assemblies
Supplied as aftermarket arms made to the listed OE references.
-
Workshop Installation
Workshop fitting and wheel alignment are required; mounting fasteners are separate.
Highlights
Six-Piece Front Set
The set contains left and right upper arms, two straight lower arms, and left and right curved lower arms.
Complete Arm Assemblies
Ball joints and bushings are already pressed into the supplied arms. These are aftermarket assemblies for the listed Model Y application; workshop installation and wheel alignment are required.
Workshop Fitting and Alignment
Mounting fasteners and alignment service are separate from the arm kit.
Kompatibilität
| Modell | Years / Version | Hinweise |
|---|---|---|
| Model Y (RWD, AWD and Performance) | 2020-2024 | Arms stamped with the listed OE numbers |
Does not fit Model Y Juniper or Model 3. Uppers stamped -00-J, 1188321/1188326 or 1288321/1288326, straight arms stamped 1044341/1288341, and curved arms stamped 2188354/2188359 or an earlier number are not listed for this kit.
Technische Daten
| Produkttyp | Front control arm kit, 6 complete arm assemblies |
|---|---|
| Compatible Models | Model Y 2020-2024 (RWD, AWD, Performance when stamps match) |
| Position / Location | Front suspension: upper arms, straight lower arms and curved lower arms |
| Menge | 6 pieces: 2 upper, 2 straight lower, 2 curved lower |
| Installation Type | Workshop fitting and wheel alignment; mounting fasteners not included |
| Lieferumfang | 6 complete front arm assemblies with ball joints and bushings pressed in |
| Versandgewicht | 12.5 kg (27.6 lb) |
| OE References | 1044321-00-G, 1044326-00-G, 1188341-00-C (x2), 1044354-00-A, 1044359-00-A |
What's in the Box
- 2×Front upper arm (left and right), complete assemblies
- 2×Front lower straight arm 1188341-00-C (same part left or right)
- 2×Front lower curved (banana) arm (left and right)
Installation
- Install the complete assemblies using the correct replacement fasteners and current service procedure for the actual vehicle.
- Follow the specified bushing-positioning and torque procedure; numerical settings must come from the applicable service manual.
- Complete the required wheel alignment.
Gut zu wissen
Achtung
- Mounting fasteners, rear arms, sway-bar links and tie rods are not included.
FAQ
Which arms are included?
Two upper arms, two straight lower arms and two curved lower arms, all for the front suspension.
Does this fit Juniper or Model 3?
Juniper and Model 3 are excluded. This kit is listed for Model Y 2020–2024 when the existing arm references match.
What if the existing OE stamp differs?
The kit is built to the listed OE references; other OE families and revision letters are not listed for this kit.
Are these original Tesla-boxed arms?
These are aftermarket assemblies made to the listed OE references.
Are bolts and alignment included?
No. Mounting fasteners and workshop alignment are separate.
English 
German 
Spanish 