Performance-Inspired Carbon Fiber Spoiler for Model S
This curved carbon fiber lip spoiler follows the rear trunk edge of the Model S. Choose a glossy or matte finish and use the underside mounting adhesive for installation without drilling.
- Carbon Fiber
- Glossy or Matte
- Adhesive Mount
- Trunk Lip
Características principales
-
Performance-inspired profile
A curved lip spoiler follows the Model S rear trunk edge.
-
Carbon fiber finish
A visible woven carbon surface adds detail to the rear of the car.
-
Two finishes
Choose Glossy / TSL8316 or Matte / TSL8316-matte.
-
Adhesive mounting
The spoiler has an adhesive strip along its underside for installation without drilling.
-
Trunk-edge fit
Test the complete profile against the actual trunk lid before removing the adhesive backing.
-
Single spoiler
The selected finish supplies one spoiler; installation cleaners and tools are separate.
Aspectos destacados
Curved Rear-Trunk Profile
The low lip profile follows the trunk edge and adds a woven carbon accent to the rear. The installation photograph shows its position.
Underside Adhesive Mounting
A mounting strip runs along the underside of the spoiler. Dry-fit the full edge before exposing the adhesive, then clean the surface and press the strip down to bond.
Glossy or Matte Finish
Choose Glossy / TSL8316 or Matte / TSL8316-matte. The visible woven surface is a styling detail; the selected finish does not change the need for a matched trunk contour and properly cured attachment.
Compatibilidad
| Modelo | Years / Version | Notas |
|---|---|---|
| Model S | 2014–2025 | Glossy / TSL8316 or Matte / TSL8316-matte; including Plaid. |
Fits Model S 2014–2025. Performance-inspired styling; not an original Tesla part.
Especificaciones
| Tipo de producto | Performance-inspired trunk lip spoiler |
|---|---|
| Compatible Models | Model S 2014–2025, including Plaid |
| Position / Location | Rear trunk-lid upper edge |
| Material | Carbon fiber |
| Surface Finish | Glossy or Matte |
| Cantidad | 1 spoiler in selected finish |
| Installation Type | Adhesive mounting without drilling |
| Peso del envío | 850 g |
What's in the Box
- 1×Trunk spoiler in the selected finish, with mounting adhesive
Instalación
- Dry-fit and center the spoiler with the adhesive liner in place.
- Clean the compatible mounting surface, removing wax and contamination without damaging paint or wrap, and allow it to dry. The installation guide specifies 15–30°C (59–86°F); also follow the supplied adhesive requirements.
- Remove the liner, align once and apply even pressure along the mounting edge. Use suitable temporary holding tape if directed, protecting the vehicle finish.
- The installation guide specifies 24 hours of temporary support and at least 48–72 hours before washing or high-speed driving. Full cure time depends on conditions.
Conviene saber
Precaución
- Test the full mounting edge against the actual trunk contour before removing adhesive backing. Do not stack this spoiler over another.
- Use preparation products compatible with the vehicle paint or wrap, and follow the actual adhesive instructions for temperature, pressure and full cure.
Cuidado
- Clean with pH-neutral car soap and a soft cloth. Avoid automated car washes for the first seven days and until the adhesive has fully cured.
- Avoid direct pressure-washer jets at the mounting edge.
Preguntas frecuentes
Which finishes can I choose?
Glossy / TSL8316 or Matte / TSL8316-matte. Both are the same Performance-inspired trunk-spoiler style.
Does installation require drilling?
No. This spoiler uses an underside adhesive mounting strip.
When can I wash the car after fitting?
Allow at least the installation guide’s 48–72 hours and follow the adhesive full-cure requirements for the actual conditions. Avoid automated car washes for the first seven days and until full cure.
What is included?
One spoiler in the selected finish with mounting adhesive. Preparation cleaner, cloth and holding tape are separate.
English 
German 
Spanish 