Real Carbon Fiber Corners for Your Front Bumper
This real carbon fiber trim pair covers the front bumper corners of the listed Model Y Juniper, Model YL and Model 3 Highland configurations. Pre-applied 3M tape and screws into the factory mounting points provide a no-drill fitting method. Available in a glossy or matte finish.
- Real Carbon Fiber
- No-Drill Install
- Pre-Applied 3M Tape
- Glossy or Matte
- Ajuste específico del modelo
Características principales
-
Real Carbon Fiber
A woven carbon fiber finish is available in glossy or matte.
-
No-Drill Installation
Pre-applied 3M tape and factory mounting points with included screws mean no drilling, cutting or bumper removal
-
Corner Coverage
The trim overlays the front bumper corner area and adds a visible carbon-fiber accent.
-
Ajuste específico del modelo
Made for Model Y Juniper, Model YL, Model 3 Highland and the Performance versions
-
Complete Pair
Left and right trim pieces come with 8 mounting screws
-
Glossy or Matte Look
Glossy gives a deeper wet look, while matte gives a subtle OEM+ look
-
Fitting Estimate
Allow approximately 15–20 minutes with basic hand tools, depending on preparation and alignment.
Aspectos destacados
A Carbon Accent at the Corners
The pieces overlay the front bumper corners, adding a carbon-fiber surface over the existing trim. They do not replace careful parking or provide full bumper protection.
Real Carbon Fiber, Two Finishes
Choose glossy for a reflective carbon-weave appearance or matte for a lower-reflection finish.
No Drilling, No Bumper Removal
The trim uses pre-applied 3M tape and the factory plastic mounting points with the included screws, so no drilling or cutting is required.
Clear Fitment
It fits Model Y Juniper Premium (2025+), Model YL (2026+), Model 3 Highland (2024+) and the 2025+ Performance versions. It does not fit Model Y 2020–2024 or Model 3 2017–2023.
Compatibilidad
| Modelo | Years / Version | Notas |
|---|---|---|
| Model Y Juniper Premium | 2025+ | Fits |
| Model YL | 2026+ | Fits |
| Model 3 Highland | 2024+ | Fits |
| Model 3 Performance | 2025+ | Fits |
| Model Y Performance | 2025+ | Fits |
Fits Model Y Juniper Premium 2025+, Model YL 2026+, Model 3 Highland 2024+, and 2025+ Model 3 and Model Y Performance. Does not fit Model Y 2020–2024 or Model 3 2017–2023.
Especificaciones
| Tipo de producto | Front bumper corner trim, left and right pair |
|---|---|
| Compatible Models | Model Y Juniper Premium (2025+), Model YL (2026+), Model 3 Highland (2024+), Model 3 Performance (2025+), Model Y Performance (2025+) |
| Position / Location | Front bumper corners |
| Material | Real carbon fiber |
| Surface Finish | Glossy carbon fiber or Matte carbon fiber |
| Cantidad | 2 trim pieces (left and right) |
| Installation Type | Pre-applied 3M tape plus screws into the factory mounting points; no drilling |
| Installation Time | Approximately 15–20 minutes |
| Drilling Required | No |
| Contenido del paquete | 2 corner trim pieces with pre-applied 3M tape, 8 mounting screws |
| Peso del envío | 1.4 kg (3.1 lb) |
What's in the Box
- 2×Front Bumper Corner Trim Pieces (Left and Right) with Pre-Applied 3M Tape
- 8×Mounting Screws
Instalación
- Clean and dry the front bumper corner area.
- Peel the pre-applied 3M tape backing and align the trim to the bumper corner.
- Press firmly along the trim to set the adhesive.
- Align the trim holes with the factory mounting points and secure with the included screws; no drilling is required.
- Wait 24 hours before high-pressure car washing.
Conviene saber
Precaución
- Not for Model Y 2020–2024 or Model 3 2017–2023.
- Wait 24 hours before high-pressure washing.
- It adds a protective layer but is not a substitute for careful driving or full bumper protection.
Cuidado
- Avoid high-pressure washing for at least 24 hours after installation, and avoid directing the water jet at trim edges.
Preguntas frecuentes
Do I need to drill holes in my car?
No. The trim comes with pre-applied 3M tape and uses the factory mounting area, and the included screws fasten into the existing plastic mounting points.
Is this real carbon fiber?
Yes. The trim is made from real carbon fiber and is available in a glossy or matte finish.
Will it protect against curb rash?
It adds an outer layer over the bumper corner area. It is not a guarantee against curb damage or a substitute for careful driving.
How can I remove the trim later?
Remove the mounting screws first. Use mild warmth and dental floss or fishing line to carefully separate the tape, then test an automotive adhesive remover on a small area before cleaning residue. Paint condition can affect removal.
English 
German 
Spanish 